+86-133 5778 8080
Home / News
Industry News 2026-11-13

Choosing a CNC Machine Tool Manufacturer for Oilfield Equipment: What to Verify

A casing and tubing shop orders a CNC lathe for 5-1/2 in. couplings, cuts a clean first article, then watches pitch diameter creep toward the top of ...
Industry News 2026-11-11

How CNC Milling Machines Process Screw Pump Rotors in Oilfield Applications

CNC milling machines make screw pump rotors by generating a helical profile through coordinated rotary and linear motion. In oilfield progressing ca...
Industry News 2026-11-06

CNC Pipe Threading Lathe: Evaluating Machining Accuracy and Thread Capacity

Evaluating a CNC pipe threading lathe comes down to two separate tests: whether it can hold thread geometry across a batch, and whether it can cut t...
Industry News 2026-11-04

Oilfield Pipe Processing Equipment: Building Drill Pipe and Coupling Production Lines

Most drill pipe and coupling lines are planned around a lathe purchase and then run into trouble at the station nobody sized properly: the bucking u...
Industry News 2026-10-30

Evaluating Machining Accuracy and Efficiency When Buying Oilfield Machine Tools

Put a ring gauge on the first coupling that comes off a new lathe and it will almost always pass. Run that same machine for four hours on P110 heavy-...
Industry News 2026-10-28

Key Factors to Consider When Selecting a Drill Pipe Joint and Coupling Lathe

Nobody buys a drill pipe joint and coupling lathe twice by accident. Shops that get this decision wrong usually find out in one of two places: at the...
Industry News 2026-10-23

Drill Pipe Repair Machining: Equipment Requirements for Reliable Thread Restoration

A wiped pin on a 5 1/2 in drill pipe arrives in the repair bay with three problems at once: galled thread crests, a shoulder face brinelled by the po...
Industry News 2026-10-21

CNC Pipe Threading Lathe vs Conventional Lathe: Oil Pipe Processing Differences

Ten joints into a casing coupling run, a threading operator checks standoff with a gauge, gets a clean reading, and then finds the twelfth piece out ...
Industry News 2026-10-16

What Buyers Should Consider When Sourcing a CNC Hard Banding Machine for Drill Pipes

A hardbanded tool joint that fails a bend test or a casing-wear check does not fail on the rig floor. It fails at the bench, after the wire, shieldin...
Industry News 2026-10-14

Deep Hole Drilling Machines for Drill Collars: Applications & Selection Factors

Three 6-3/4 in drill collars scrapped in one week usually share the same cause: the bore drifted in the last meter, wall thickness ran out of toleran...
Industry News 2026-10-09

How to Match CNC Machining Equipment with Oilfield Pipe and Coupling Sizes

A shop orders a CNC pipe threading lathe rated for 5-1/2 in. casing, then wins a contract that includes coupled joints. The pipe body measures 139.7 ...
Industry News 2026-10-07

How to Choose the Right CNC Pipe Threading Lathe for Oilfield Pipe Processing

A shop that buys a threading lathe sized for 2 3/8-inch tubing usually finds out it was the wrong machine on the day a casing order arrives. The spin...
Industry News 2026-09-30

Hydraulic vs Mechanical Bucking Unit: Torque Control, Cost, and Maintenance Compared

The short answer When you compare a hydraulic bucking unit vs mechanical bucking unit, the first difference is not price; it is how torque is control...
Industry News 2026-09-23

Bucking Unit vs Pipe Torque Machine: Key Differences and How to Choose

When a workshop starts processing casing and tubing, one of the first equipment decisions is how to make up and break out threaded connections. A buc...
Industry News 2026-09-16

How Bucking Unit Manufacturers Ensure Quality: Torque, Standards & Testing

A bucking unit that delivers consistent, accurate torque is the difference between a connection that survives years of downhole service and one that ...